膜科学与技术

聚乙二醇添加剂对聚砜超滤膜结构和性能的影响研究

作者：安亚欣，张奇峰，张所波

单位：中国科学院长春应用化学研究所，生态环境高分子材料重点实验室，长春 130022

关键词：聚砜；超滤膜；添加剂

出版年,卷(期):页码： 2015,35(5):64-70

摘要：

本文采用聚乙二醇（PEG）为添加剂，1-甲基-2-吡咯烷酮（NMP）为溶剂制备了聚砜（PSF）超滤膜。系统研究了PEG的含量和分子量对PSF膜的断面结构、平均孔径（r）、孔隙率（ε）、纯水通量（PWF）、接触角（CA）的影响。膜断面的SEM照片表明：随着铸膜液中PEG含量的增加或PEG分子量的增大，断面的泪滴状孔逐渐消失，靠近膜上表面的海绵层厚度增加。膜的r、ε、PWF和CA变化趋势为：随着PEG含量的增加，膜的r先增加后减小再增加，ε先略有增加后明显增加，PWF与r的变化趋势一致；随着PEG分子量的增加，膜的r先增加后降低再升高，最后迅速下降，膜的ε先增加后降低，PWF和r的变化趋势一致。当PEG400含量增大（>=16.8%）时，或PEG分子量的增加（>=2000）时，CA降低。

Polysulfone(PSF)membrane was prepared by using PSF/N-methyl-2-pyrrolidone (NMP)/poly(ethylene glycol) (PEG) castingsolution and water coagulant. Effects of the content and molecular weight of PEG on the morphology, the mean pore radius(r), porosity(ε), pure water flux(PWF) and contact angel(CA) of PSF membrane were systematically investigated. SEM images of the PSF membranes showed that the teardrop-shaped pores disappearedand the thickness of the sponge layer near the top surface of the membrane increased as the content or molecular weight of PEG additive increased,. As the content of PEG400 increased in the membrane dope solution, r increased firstly, then decreased, and finally increased again; εfirst increased slightly, and then increased sharply; the trend of PWF was consistent with that of r. As the molecular weight of PEG increased, r increased firstly, then decreased slightly, and then increased sharply, finally decreased sharply;ε increased, and then decreased sharply; the trend of PWF was consistent with that of r. The CA of PSF membrane decreased when PEG400 content increased (>=16.8%) or the molecular weight of PEG increased (>=2000).
KEY WORDS:

安亚欣（1989），女，河北石家庄，硕士，研究实习员，从事高分子膜的制备研究

参考文献：

[1] 胡增,陈峰,单永广,等. 聚哌嗪酰胺复合纳滤膜的制备及表征[J]. 水处理技术,2013(39):19-22
[2]俞三传,金可勇,潘巧明,高从堦.聚哌嗪酰胺复合纳滤膜研制[J]. 膜科学与技术,2001(21)：1-3
[3]邹高辉,陈寅生.聚砜超滤膜的制备及结构性能研究[J]. 过滤与分离, 2007 (17):11-14
[4]雷晓慧,丁雪佳,何金迎,等. 添加剂对聚砜膜结构和性能的影响[J]. 化工进展，2013(32):1866-1869
[5]Swapna Rekha Panda • Sirshendu De, Role of polyethylene glycol with different solventsfor tailor-made polysulfonemembranes[J],Journal of Polymer Research, 2013(20):179-194
[6]LeeC J,Wang S S, LinG C. Pilot Production of Polysulfone Hollow Fiber for Ultrafiltration Using Orthogonal Array Experimentation[J], Industryand Engineeringof Chemistry Research, 1996(34): 813-819.
[7]Zhang Z H, An Q F, Liu T, et al..Fabrication of polysulfone ultrafiltration membranes of a density gradient cross section with good anti-pressure stability and relatively high water flux[J],Desalination,2011 (269) :239–248
[8]Jung B, YoonJ K, KimB, et al. Effect of molecular weight of polymeric additives on formation, permeation properties and hypochlorite treatment of asymmetric polyacrylonitrile membranes[J], Journal of Membrane Science,2004 (243):45–57
[9]Lafreniere L Y, TalbotF D F. Effect of Polyvinylpyrrolidone Additive on the Performance of Polyethersulfone Ultrafiltration Membrane[J], Industryand Engineeringof Chemistry Research, 1987(26):2385-2389
[10]ZhangY Z, LiH Q, LiH, et al.. Preparation and characterization of modified polyvinyl alcohol ultrafiltration membranes[J], Desalination 2006(192):214–223
[11]SadrzadehM, BhattacharjeeS. Rational design of phase inversionmembranes by tailoring thermodynamics and kinetics of casting solution using polymer additives[J], Journal of MembraneScience, 2013(441):31–44
[12]IdrisaA, ZainN Mat, NoordinM Y. Synthesis, characterization and performance of asymmetric polyethersulfone (PES) ultrafiltration membranes with polyethylene glycol of different molecular weights as additives[J]. Desalination,2007(207):324–339
[13]KimJH, LeeK H.Effect of PEG additive on membrane formation by phase inversion[J],Journal of Membrane Science, 1998 (138):153-163

服务与反馈：

【文章下载】【加入收藏】

《膜科学与技术》编辑部地址：北京市朝阳区北三环东路19号蓝星大厦邮政编码：100029 电话：010-64426130/64433466 传真：010-80485372邮箱：mkxyjs@163.com