膜科学与技术

一体式A2/O-MBR内的DO分布模拟及影响因素研究

作者：袁星，杨敏，罗南，樊耀波

单位：中国科学院生态环境研究中心，北京 100085

关键词：计算流体力学；氧传质；一体式A2/O-MBR；DO分布

出版年,卷(期):页码： 2016,36(1):61-71

摘要：

基于计算流体力学（CFD）的方法，将氧传质模型与之进行耦合，对一体式A2/O-MBR内部流场特性及溶解氧（DO）浓度分布进行模拟，并且分析了曝气量、污泥浓度及气泡直径对DO分布的影响。研究结果表明，随着曝气量的增大，DO浓度升高，好氧区域范围扩大；随着污泥浓度的增大，DO浓度随之降低，而对液体流速的影响不明显；随着气泡直径的增大，DO浓度明显降低，膜面剪切力则明显升高，而反应器内部速度场变化不显著。研究发现存在一个较低的曝气量和适中的气泡直径，使一体式A2/O-MBR可在较低能耗的条件下，较好的满足脱氮除磷条件及内部流场强度的需求。

The fluid characteristics and the distribution of dissolved oxygen in an A2/O-MBR were simulated by coupling computational fluid dynamics (CFD) with the oxygen mass transfer model in this paper. And the factors influencing on the distribution of dissolved oxygen considered for this work were aeration rate, sludge concentration and bubble diameter. The results indicated that the higher aeration rate could result in higher dissolved oxygen concentration and bigger aerobic zone, however, on the contrary, the higher sludge concentration would cause lower dissolved oxygen concentration; with increasing the bubble diameter, the dissolved oxygen concentration decreased significantly and the wall shear stresses on membrane were increased sharply but the liquid velocity in the A2/O-MBR was not affected obviously. It also showed that there may be a lower value of aeration rate and a moderate data of bubble diameter to establish the desire conditions for denitrification and phosphorus removal with lower energy consumption in the A2/O-MBR.

第一作者简介：袁星（1989-），女，浙江嘉兴人，硕士生，研究方向为计算流体力学（CFD）与氧传质模型耦合方法在一体式A2O-MBR中的应用研究，E-mail:smile19891027@126.com.*通讯作者，E-mail:ybfan@rcees.ac.cn

参考文献：

[1] 徐荣乐, 樊耀波, 张晴, et al. A~2/O-MBR研究与应用进展[J]. 膜科学与技术, 2013, (06): 111-118.
[2] 赵曙光, 姜志琛, 徐东耀, et al. 新型一体化A~2/O-MBR曝气能效研究[J]. 水处理技术, 2014, (12): 79-82.
[3] 王福军, 黎耀军, 王文娥, et al. 水泵CFD应用中的若干问题与思考[J]. 排灌机械, 2005, (05): 5-14.
[4] Fayolle Y, Cockx A, Gillot S, et al. Oxygen transfer prediction in aeration tanks using CFD[J]. Chemical Engineering Science, 2007, 62(24): 7163-7171.
[5] Guo X, Zhou X, Chen Q, et al. Flow field and dissolved oxygen distributions in the outer channel of the Orbal oxidation ditch by monitor and CFD simulation[J]. 2013, - 25(- 4): - 651.
[6] Le Moullec Y, Gentric C, Potier O, et al. CFD simulation of the hydrodynamics and reactions in an activated sludge channel reactor of wastewater treatment[J]. Chemical Engineering Science, 2010, 65(1): 492-498.
[7] Guimet V, Honore T, Audic J M, et al. Rheology and oxygen transfer in CFD models for wastewater[J]. Progress in Computational Fluid Dynamics, 2007, 7(2-4): 219-229.
[8] Cockx A, Do-Quang Z, Audic J M, et al. Global and local mass transfer coefficients in waste water treatment process by computational fluid dynamics[J]. Chemical Engineering and Processing: Process Intensification, 2001, 40(2): 187-194.
[9] Lei L, Ni J. Three-dimensional three-phase model for simulation o f hydrodynamics, oxygen mass transfer, carbon oxidation, nitrification and denitrification in an oxidation ditch[J]. 2014, - 53(- 0): - 214.
[10] 杨寅. 氧化沟优化运行的CFD模拟及实验研究[D]. 华中科技大学, 2011.55-60.
[11] Casey E, Glennon B, Hamer G. Oxygen mass transfer characteristics in a membrane-aerated biofilm reactor[J]. Biotechnology and Bioengineering, 1999, 62(2): 183-192.
[12] 周晓伟, 张新玉, 杨斌, et al. 超重力旋转床气相传质CFD仿真分析及实验验证[J]. 化工进展, 2014, (04): 837-842+860.
[13] 马友光, 余国琮. 气液界面传质机理[J]. 化工学报, 2005, (04): 580-584.
[14] 高习群. 气液界面传质机理与强化[D]. 天津大学, 2008.4-5.
[15] 李凌云, 李论, 彭永臻, et al. 活性污泥系统动态比耗氧速率的检测与可行性验证[J]. 北京工业大学学报, 2011, (09): 1430-1434.
[16] 张晴. 气升循环分体式MBR的计算流体力学模拟与优化[D]. 中国科学院生态环境研究中心, 2013.68-69.
[17] 上海斯纳普膜分离科技有限公司. SINAP 平板膜产品技术手册. 2010.
[18] 苑志华, 杨晓永, 于昌平. A~2O-MBR工艺脱氮除磷的性能及稳定性[J]. 水处理技术, 2013, (09): 97-100.
[19] 范海涛, 王洪臣, 齐鲁, et al. 污泥浓度对微孔曝气氧传质过程的影响[J]. 环境工程学报, 2012, (12): 4305-4309.
[20] 郭瑾珑, 程文, 周孝德, et al. 小气泡扩散曝气氧传质速率研究[J]. 西安理工大学学报, 1999, (04): 86-90.
[21] Wei P, Zhang K, Gao W, et al. CFD modeling of hydrodynamic characteristics of slug bubble flow in a flat sheet membrane bioreactor[J]. Journal Of Membrane Science, 2013, 445: 15-24.

服务与反馈：

【文章下载】【加入收藏】

《膜科学与技术》编辑部地址：北京市朝阳区北三环东路19号蓝星大厦邮政编码：100029 电话：010-64426130/64433466 传真：010-80485372邮箱：mkxyjs@163.com