膜科学与技术

成膜基质对炭膜结构与气体分离性能的影响

作者：张兵¹ 党晓龙¹ 吴永红¹ 于智学¹ 王同华²

单位： 1. 沈阳工业大学石油化工学院，辽宁辽阳 111003；

关键词：成膜基质；炭膜；孔结构；渗透性

出版年,卷(期):页码： 2014,34(6):17-21

摘要：

以间苯二酚-甲醛为碳源，F127为添加剂，经成膜与炭化得到炭膜。通过热失重分析、红外光谱、元素分析及透射电镜从微观上分析了前驱体的热解过程及碳结构演变。采用X射线衍射及氮气吸附技术分别测定了炭膜碳结构与孔结构。研究了成膜基质表面疏水性对成膜过程的收缩率、碳结构、孔结构及气体分离性能的影响。结果显示，成膜基质对炭膜微观结构与分离性能影响显著。疏水性较大的玻璃比聚四氟乙烯与不锈钢更有助于减小成膜过程中径向收缩率，并得到高比表面积与孔体积的炭膜，其对O2/N2选择性高达10以上。

Carbon membranes were prepared using resorcinol-formaldehyde as precursor and F127 as additives, through the processes of membrane-forming and carbonization. The thermal stability of precursors and their formation of carbon structure were analyzed by thermogravimetry analysis, Infrared spectroscopy, elemental analysis and transmittance electron microscopy at microscale level. The carbon structure and porous structure of carbon membranes were also measured by X-ray diffraction and N2 adsorption technique. The surface hydrophobicity of membrane-formation substrate was correlated with the shrinkage during membrane formation, carbon structure, porous structure and gas separation performance of resultant carbon membranes. Results have shown that membrane-formation substrate definitely has great effect on the microstructure and separation performance of carbon membranes. Compared with polytetrafluoroethylene and stainless steel, glass plate with higher hydrophobicity is beneficial for deceasing radial shrinkage during membrane formation, resulting into larger specific surface area and pore volume in carbon membranes. A satisfactory O2/N2 selectivity is attained above 10 for carbon membranes formed on glass plate.

张兵（1977－），男，博士，副教授，主要从事炭膜制备及应用研究；

参考文献：

[1] Ismail A F, Rana D, Matsuura T, et al. Carbon-based membranes for separation processes[M]. Springer New York Dordrecht Heidelberg London, 2011.
[2] Ismail A F, Saufi S M. Fabrication of carbon membranes for gas separation–a review[J]. Carbon, 2004, 42: 241–259.
[3] Tin P S, Xiao Y, Chung T-S. Polyimide-carbonized membranes for gas separation: structural, composition, and morphological control of precursors[J]. Sep Puri? Rev, 2006, 35: 285–318.
[4] Salleh W N W, Ismail A F, Matsuura T, et al. Precursor selection and process conditions in the preparation of carbon membrane for gas separation: a review[J]. Sep Puri? Rev, 2011, 40: 261–311.
[5] 张兵,王同华,呼立红,等. 聚酰亚胺基气体分离炭膜的进展[J]. 膜科学与技术, 2007, 27: 97-101.
[6] Wang C, Mao Y, Wang D, et al. Fabrication of highly ordered microporous thin films by PS-b-PAA self-assembly and investigation of their tunable surface properties[J]. J Mater Chem, 2008, 18: 683–690.
[7] Fuertes A B, Centeno T A. Preparation of supported carbon molecular sieve membrane [J]. Carbon, 1999, 37: 679–684.
[8] Tseng H-H, Shih K, Shiu P-T, et al. Influence of support structure on the permeation behavior of polyetherimide-derived carbon molecular sieve composite membrane[J]. J Membr Sci, 2012, 405–406: 250–260.
[9] 刘诗丽. 聚醚砜酮预氧化机理及其炭膜制备工艺优化[D]. 大连：大连理工大学博士学位论文, 2008.
[10] 孟繁妍.有序纳米孔炭膜的制备及表征[D]. 沈阳: 沈阳工业大学硕士学位论文, 2012.
[11] 同小刚，王芬，冯海涛. 疏水型二氧化硅气凝胶薄膜的制备[J]. 中国陶瓷, 2006, 42：29–31.
[12] Zhang B, Wang T, Zhang S, et al. Preparation and characterization of carbon membranes made from poly(phthalazinone ether sulfone ketone) [J]. Carbon, 2006, 44: 2764-2769.
[13] 马伟.酚醛树脂的热解研究[D]. 重庆: 重庆大学硕士学位论文, 2007.
[14] 李淑君，李坚，刘一星，等. 用TG-DSC-FTIR联用技术研究酚醛树脂的热解行为[J]. 东北林业大学学报，2007, 35: 56-58.
[15] Lin H P, Chang-Chien C Y, Tang C Y, et al. Synthesis of p6mm hexagonal mesoporous carbons and silicas using pluronic F127-PF resin polymer blends [J]. Microporous and Mesoporous Mater, 2006, 93: 344–348.
[16] 姜华玮，王同华，李琳，等. 有序介孔复合炭膜的制备及其性能研究[J]. 新型炭材料, 2010, 25: 273–278.

服务与反馈：

【文章下载】【加入收藏】

《膜科学与技术》编辑部地址：北京市朝阳区北三环东路19号蓝星大厦邮政编码：100029 电话：010-64426130/64433466 传真：010-80485372邮箱：mkxyjs@163.com